A Pedido de 20 a 30 Dias CISCO1921/K9 Overview The Cisco 1921 Integrated Services Router (ISR) delivers highly secure data, mobility, and application services. Cisco1921-K9 Cisco 1921 Router ISR G2 2 integrated 10/100/1000 Ethernet ports: GE0/0&GE0/1 2 enhanced High-Speed WAN Interface Card (EHWIC) slots that can host 2 single wide or 1 double wide EHWIC module Support fully integrated power distribution to modules supporting 802.3af Power over Ethernet (PoE) and Cisco Enhanced PoE Highly secure collaborative communications with Group Encrypted Transport VPN, Dynamic Multipoint VPN, or Enhanced Easy VPN Integrated threat control using Cisco IOS Firewall, Cisco IOS Zone-Based Firewall, Cisco IOS IPS, and Cisco IOS Content Filtering LED area description · SYS: Solid green ---normal operation. Blinking green ---System is booting or is in ROM monitor mode. Amber ---System error. Off ---Power is off or system board is faulty. · ACT: Solid or blinking ---any packets are transmitted/received on any WAN/LAN, or when monitoring system activity. · PoE: Green ---PoE is available. Amber ---Power supply is not supplying PoE power. · S (Speed): 1 blink + pause ---GE port operating at 10 Mb/s. 2 blink + pause ---GE port operating at 100 Mb/s. 3 blink + pause ---GE port operating at 1000 Mb/s. · L (Link): Green ---GE link is established. Off ---No GE link is established. Note: · 1 integrated EHWIC slots for flexible configurations & support of two modules: 1 double wide HWIC-D or single wide EHWIC/HWIC module; or 2 single wide EHWIC/HWIC module . (Each HWIC Slot offers high data throughput capability with up to 1.6 Gbps aggregate towards the router processor and up to 2 Gbps aggregate to other module slots over MultiGigabit Fabric (MGF)). · 1 AUX port (auxiliary port) ---RJ-45 connectors for Remote configuration. · GE 0/0 & 0/1---Two Gigabit Ethernet ports (RJ-45 connectors). · High-speed USB 2.0 ports enable another mechanism secure token capabilities and storage. Key Features of CISCO1921/K9 Cisco 1921 Product FAQ Q: Please urgently confirm that this Router CISCO1921/K9 has BGP (Border Gateway Protocol). A: YES, BGP is supported by almost all Cisco Routers. Q: Cisco 1921 CAN support Vwic2-2MFT-T1/E1? A: YES. Q: The 1900 series routers which IOS supports IP SLA? A: The dedicated or SLAs router is used exclusively for Cisco IOS IP SLA operations and is connected to the edge routers to simulate the customer network traffic. It is typically a Cisco 1900, 2800, 2900, 3800, 3900 or 7200 Series Router. Q: I have a 1921 router. Using usb cable I can connect to the console but cannot get the router into rommon mode. I saw a post for a 1941 router where you can remove the flash to get it into rommon mode, but the 1921 flash cannot be removed. I am using Mac terminal and screen command but am not able to send break signal. would love to know if it’s possible. A: I think you can. The CF is "hidden" behind a dust cover. The slots are located at the BACK of the unit, to the left. The back is where the ports and EHWIC slots are. Q: The problem i'm running into is all the sample configs for Cisco 1921 sample working config for VDSL with a VA-DSL-A card, i'm finding are for much older code, i need it for a 1921 with version 15.2(3)T. A: Hi, I believe you have an EHWIC-VA-DSL-A card installed on the C1921 device. The sample configuration for the same would be as follows, 1. Configure the Controller, 2. Configure the Ethernet interface & its sub-interface, 3. Configure the Dialer interface and as per you requirements, you can configure the Authentication, IP addressing etc. Q. If I purchased a Cisco ISR G2 router on Cisco IOS Software Release 15.0(1) M before the limitation was imposed, what should I do? And should I need to upgrade my Cisco IOS Software? A: Assuming that you already have purchased the securityk9 package for encryption, you must purchase a HSEC-K9 license as a spare. Q.Why do I need to purchase the SEC-K9 license as a spare? A. If you purchase a Cisco ISR G2 chassis and later decide to turn on security features, you must buy a SEC-K9 license. The administrator must download the license to the router and follow the license installation instructions that come with the license to be able to use the security features on the router. Q. On the Cisco ISR G2 routers with the SEC-K9 license, what tunnel count and performance throughput are available? A. The SEC-K9 permanent licenses apply to the Cisco 1900, 2900, and 3900 ISR G2 platforms; these licenses limit all encrypted tunnel counts to 225 tunnels maximum for IP Security (IPsec), Secure Sockets Layer VPN (SSL VPN), a secure time-division multiplexing (TDM) gateway, and secure Cisco Unified Border Element (CUBE) and 1000 tunnels for Transport Layer Security (TLS) sessions. The SEC-K9 license limits encrypted throughput to less than or equal to 85-Mbps unidirectional traffic in or out of the ISR G2 router, with a bidirectional total of 170 Mbps. This requirement applies for the Cisco 1900, 2900, and 3900 ISR G2 platforms. CISCO1921/K9 Specifications Product Specifications of Cisco 1921 Integrated Services Router Cisco 1921 Integrated Services Router Services and Slot Density Embedded hardware-based cryptography acceleration (IPsec + SSL) Yes RJ-45 onboard LAN 10/100/1000 ports 2 EHWIC slots 2 Doublewide EHWIC slots (use of a doublewide EHWIC slot will consume 2 EHWIC slots) 1 Cisco Integrated Services Module (ISM) slots 0 Memory (DDR2 DRAM): Default/Maximum 512 MB/512 MB USB flash memory (internal): Default/maximum 256 MB/256 MB External USB flash-memory slots (Type A) 1 USB console port (mini-Type B) (up to 115.2 kbps) 1 Serial console port (up to 115.2 kbps) 1 Serial auxiliary port (up to 115.2 kbps 1 Integrated power supply AC Power-supply options POE (external) Redundant-power-supply support No Power Specifications AC input voltage 100--240V ~ AC input frequency 47--63 Hz AC input current range AC power supply (maximum) (amps) 1.5--0.6 AC input surge current <50A Typical power (no modules) 25W Maximum power capacity with AC power supply 60W Maximum power capacity with PoE power supply (platform only) 70W Maximum PoE device power capacity with PoE power supply 80W Physical Specifications Dimensions (H x W x D) 1.75 x 13.5 x 11.5 in. Rack height 1RU Rack-mount 19in. (48.3 cm) EIA optional Wall-mount (refer to installation guide for approved orientation) Yes Weight - with AC power supply (no modules) 12 lb Weight - with PoE power supply (no modules) 12.8 lb Maximum weight - fully configured 14 lb Airflow Back to Sides Environmental Specifications Operating Condition Temperature: 5906 feet (1800m) maximum altitude 0--40°C (32--104°F) Temperature: 9843 feet (3000m) maximum altitude 0--25°C (32--77°F) Altitude 3000m (10000 ft) Humidity 10 to 85% RH Acoustic: Sound pressure (typical /maximum) 32.99/58.33 dBA Acoustic: Sound power (typical/maximum) 41.99/67.22 dBA Transportation/Storage Condition Temperature --40 to 70°C (--40 to 158°F) Humidity 5 to 95% RH Altitude 4570m (15000 ft) Regulatory Compliance Safety UL 60950-1 CAN/CSA C22.2 No. 60950-1 EN 60950-1 AS/NZS 60950-1 IEC 60950-1 EMC 47 CFR, Part 15 ICES-003 Class A EN55022 Class A CISPR22 Class A AS/NZS 3548 Class A VCCI V-3 EN 300-386 EN 61000 (Immunity) EN 55024, CISPR 24 EN50082-1 Telecom TIA/EIA/IS-968 CS-03 ANSI T1.101 IEEE 802.3 RTTE Directive WARRANTY 100% Quality Assurance: All items are ORIGINAL and GENUINE only. Item conditions are "New Sealed" or "Used / Refurbished". Used & refurbished items are fully tested with good conditions by Cisco-certified Engineers. 100% Money Back Guarantee: You can contact our customer service team to exchange or return any product that you bought from us. Free CCIE Technical Support Our FREE Cisco CCIE Expert Consultancy Support is over the phone, by chat, by email or by login remotely. Flexible Secure Payment & Shipment Verified authorization: Mcafee Secure, VeriSign Secured Return Material Authorization (RMA) Process Standard Hardware Warranty Policy : Original new sealed Cisco product: 1 Year Used Cisco product: 3 Month The Support Contacts : If your Cisco products failed, you must contact your sales representative to verify product failure. If the problem still can't correct by remote support methods i.e. email or phone support, the RMA procedure will issue. The RMA Confirmation : Your sales representative will send you RMA form. (see attachment. PO No.; Product Serial No.; Description of Failure or Problem) You Fill it and send back to sales representative. RMA Return Shipment : A : After ot RMA form, sales representative will tell you returned instruction by email, including shipping address and special shipping invoice. B : Returned products have to be packed properly to avoid damage during delivery. C : All accessories and user documentations should be returned. D : Once shipped, pls tell sales representative tracking No. immediately. Delivery Charges : The Customer is responsible for paying shipment charges when returning to us; We will pay for shipment of the repaired items back to the customer RMA Turnaround Time : The defective products will be sent to Cisco Distributor for repair. Within four weeks after receipt of returned item, the repaired or replacement item will be ready for return shipment. Then item will be shipped to customer by Express such as DHL or Fedex.